Pagina 1 van 1

Scoops motorkap Mustang bj97

Geplaatst: ma 09 jul, 2018 14:34
door yellow
Hallo

Hoe krijg ik die kleine scoops in de motorkap en de grote in het achhter spatbord los?
Zijn dat gewoon klemmetjes?

Re: Scoops motorkap Mustang bj97

Geplaatst: ma 09 jul, 2018 16:08
door Mack
Edit, zie volgende post

Afbeelding

Re: Scoops motorkap Mustang bj97

Geplaatst: ma 09 jul, 2018 16:11
door Mack
The bezel must be removed to access the three tabs tabs that hold the honey-comb insert in place. Good news though, it's really easy. Open and prop the hood. On each side there are two 9mm nuts(don't lose the washers) you need to remove and the bezels pull straight out! You don't need to mess with the fire-proofing or anything as they are not underneath it. They are right out in the open and close to the edges of the hood. Once you remove the bezel and flip it over, press in the two bottom tabs and the insert will pivot right out. Hook the top tab of the new insert and just snap the bottom two right in! Then, replace the bezels and replace and tighten the two 9mm nuts on each one. Don't try to crank them down because they aren't very strong! Just tight enough so they don't rattle loose.

Re: Scoops motorkap Mustang bj97

Geplaatst: ma 09 jul, 2018 16:19
door yellow
Thx will try it

Frans

Re: Scoops motorkap Mustang bj97

Geplaatst: ma 09 jul, 2018 16:20
door yellow
How do you remove the big ones on the rear fenders?

Frans

Re: Scoops motorkap Mustang bj97

Geplaatst: ma 09 jul, 2018 18:16
door Mack
Je mag gewoon Nederlands tikken, hoor, ik kopieer ook maar wat ik online vind... :lol:

Volgens deze video en tekst (die ik onafhankelijk van elkaar vond) kun je de scoop alleen van binnenuit eruit halen als je de achterbank eruit haalt. Maar dat gaat over het hele ding, niet alleen het plastic dingetje. Maar ik betwijfel of je die zomaar eruit krijgt.

Nog extra moeilijk bij een 94/95 want daar was de scoop ook functioneel en zit er dus een buis achter naar de wielkast. Vanaf 96 is dit niet meer en waren de scoop alleen voor de sier.

Vanaf 7:20:
phpBB [video]

The seat bottom has two clips holding it in place. Their is a plastic tab that sticks out that you push in to release them. The tab is located in the center of each side of the seat just under the front edge of the cushion. Just start in the center of each side of the seat and feel for it or look for it and get a flat head screw driver to push the plastic tab in and the seat will pop free. There is one on each side.

As for the side panel you have to remove the phillips head screw holding the clothes hanger from the top, then you have to remove the cover and torx style bolt holding the seat belt in place, there should be another plastic push tab near the seat belt mount that has to be removed, remove the two plastic tabs holding the rubber molding in the door jamb that attaches to the side panel. The upper panel then can be pulled out and there are tabs behind it that hold it in place that just pop out.

The big lower panel has 3-4 small tabs holding it in place that are located behind the back seat (so you have to put the back seat down to reach them). There is one more plastic tab along the top, towards the back of the panel, you also have to remove the door sill plastic. At this point the panel can be pulled forward (towards the front of the car) and maneuver it out. Just be careful as there are long alignment tabs behind the panel that can snap off. Not the end of the world if they do it's just one less thing holding the panel in place.